Front and Side View of CellarPro 1800QTL-ECX wine cabinet cooling unit
Front view of CellarPro 1800-QTL-ECX Wine Cabinet Refrigeration Unit
Back view of CellarPro 1800-QTL-ECX Wine Cabinet Refrigeration Unit
Underside view of CellarPro 1800-QTL-ECX Wine Cabinet Refrigeration Unit
Control Panel of CellarPro 1800-QTL-ECX Wine Cabinet Refrigeration Unit
Bottle Probe Jack on CellarPro 1800-QTL-ECX Wine Cabinet Refrigeration Unit

1800QTL-ECX Cooling Unit by CellarPro Cooling Systems

Regular price $1,395.00
/
USD
Add Ons
?
Recommended when the cooling unit will be installed in a wine cellar, a 1/2" ID condensate fitting and 8-foot clear vinyl tube allows overflow condensation to exit from the bottom of the cooling unit.
?
When the wine cooling unit will be installed in a wine cellar with hot, humid conditions, this 100W heating element is designed to burn off excess moisture. This must be combined with either the bottom or rear condensate drain line add-on.
?
This pair of clips can attach anywhere along the front of CellarPro 1800 cooling units and offer pre-drilled slots for bolting to the ceiling of your wine cellar. The ceiling must have appropriate framing/backing to carry the weight of the cooling unit.
?
Choose this add-on if you wish to plug in your unit inside the wine cellar. This modification has the cord exiting on the left side of the unit nearer the front. Without this modification, your power cord will exit the back of your unit to be plugged in outside of the wine cellar.
?
Recommended when the cooling unit will be installed in a wine cellar, a 1/2" ID condensate fitting and 8-foot clear vinyl tube allows overflow condensation to exit from the rear of the cooling unit.
?
Choose this complementary option if you'd like your unit to exhaust from the top, instead of the standard rear venting configuration. Fresh air intake will still be from the rear of the unit.
?
Add this option if using the bottle probe and you need to add up to 25ft of cord length.
?
Add this option if using the bottle probe and you need to add up to 50ft of cord length.
?
Add this option if the units fresh air intake will be as low as 20°F. 
?
Add this option if the units fresh air intake will be below 20°F.
?

This option is strongly recommended for installations where the unit and its built-in display/control panel is not visible within the wine cellar. This panel will allow you to monitor and adjust unit settings from the location of your choice and is hard-wired to the unit (10 feet of wiring included – please contact us after ordering if you require extra wiring length)

?
Add this option for units that are not ducted on the hot side. Adheres to unit with magnetic strips. Avoid a future separate order when it comes time to change the disposable filter that comes with the unit.
?
This option is strongly recommended for the most accurate temperature measurement and is absolutely necessary when the unit is ducted into the cellar. The probe can either measure air temperature or liquid temperature inside a bottle. The probe end will cork a wine bottle to blend into your cellar. This item comes with 10 feet of cord.

IMPORTANT: Please be sure to review the add-on options above to confirm you have all accessories necessary for your particular installation. Many are factory-installed and difficult to accommodate as a separate purchase/installation.

The CellarPro 1800QTL-ECX cooling unit is intended for small to medium-sized wine cabinets and has a focus on gentle cooling and quiet operation. If you're looking to cool a small wine cellar, consider the higher-capacity 1800 series units: QT, XT, XTS or XTSX.

CellarPro 1800QTL-ECX units are the same size and capacity as Breezaire 1060 and Wine-Mate 1500 cooling units, making them a suitable option for replacement.

Note that CellarPro 1800QTL-ECX cooling unit come standard with rear ventilation. If you'd prefer hot air exhaust from the top of the unit, choose the Top Exhaust Option under Add-Ons.

All air-cooled cooling units require fresh air intake to dissipate the heat generated by the cooling unit. The fresh air intake CANNOT come from the wine cellar/cabinet space - it must come from space outside the wine cellar/cabinet.

  • Energy-efficient EC fans on both the hot and cold sides of the unit.
  • Adjustable humidity control combines a high-output compressor with flexible fan cycles to maintain a recommended level of moisture inside your cellar. 
  • Extra large coils generate maximum cooling power inside the cellar. 
  • Choose from rear (standard) or top exhaust (add-on, no extra cost)
  • Excess condensate is managed with a high-capacity stainless steel condensate pan and 100W electric heating element. 
  • Commercial-grade Electrofin coating protects the evaporator coils from leaks and corrosion. 
  • Intuitive LED display panel mounted on the unit with digital programmable thermostat is simple and easy to use. (see add-on option above for a remote display/control option).
  • Energy-saver mode, quick-chill mode, and auto-defrost cycle.
  • Temperature set point range is 47°F to 62°F when the cooling unit is installed into an appropriately sized cellar.
  • Unit operates with minimal vibrations and less noise than comparable units from other companies.
  • Audible and visual alarms and maintenance-needed indicator protect the cooling unit and the wine cellar.
  • 8 foot power cord exits from the rear of the unit and plugs into a standard 110V receptacle on a dedicated 15amp circuit. If you'd prefer to plug your unit inside the wine cellar, choose the Power Cord Modification add-on.
  • Removable steel case provides access to the internal components for servicing and repair.
  • ETL Tested and Certified to rigorous UL Standards for safety. 

View Configuration Diagrams

  • CellarPro 1800 series cooling units are self-contained and fully-charged. They are designed to be installed through-the-wall or just above the cellar in an air-conditioned space (ie. not a hot attic or other unconditioned space)
  • 1800 series units cannot be front ducted but certain models (XT and XTS) offer rear ducting with the purchase of the rear duct hood or rear duct kit add-on.
  • On the cold side, this unit intakes from the front and exhausts cold air from the bottom (so the front 8 inches of the cooling unit must be inside the cellar.)
  • This unit requires fresh air intake at the rear.
  • If the fresh air intake (on the hot side) will receive air below below 40°F, you will require a compressor heater (see add-on options above).
  • If the fresh air intake (on the hot side) will pull air below 20°F, down to -20°F, you must add both the compressor heater and fan cycling switch (see add-on options above).
  • This unit must always be installed and operated in an upright position.

Cooling Capacity:

1065 BTU/h at 55°F

Dimensions:

18” w x 16 1/2” d x 10 1/2” h

Weight:
60 lbs

Sound:
41 dBA (rear)

Power/Rating:

115V AC / 60 Hz

Compressor Amps:

- Startup (LRA): 14.2 Amps

- Running: 2.4 Amps

- Total Watts: 191

- Requires Dedicated 15-Amp Circuit (surge protector recommended)

Installation Resource Documents

Owners Manual Top/Bottom Cut Sheets
Spec Sheet Installation with a Support Shelf
Installation with Mounting Clips Front/Rear/Side Cut Sheets

Orders of this item are typically shipped within 4 – 8 business days via an LTL carrier, on a pallet.

Please note: If this unit is on backorder or subject to longer lead times, it will be noted in the main product description.

The pallet will be delivered to the first opening in your home (typically a garage).

This product is warrantied by Cellar Pro Cooling Systems.

For five years from the date of purchase, your CellarPro warranty covers the internal compressor if it proves to be defective in materials or workmanship. In addition, for two years from the date of purchase, your CellarPro warranty covers all parts and labor to repair or replace any components in the wine cooling unit that prove to be defective in materials or workmanship.

For all products covered by the terms of this warranty, CellarPro will repair or replace the original cooling unit with a new or refurbished cooling unit and, once replaced, the original cooling unit must be returned to CellarPro.

All service provided by CellarPro under the above warranty must be performed by CellarPro or a designated repair facility unless otherwise specified by CellarPro. Purchaser is responsible for shipping the wine cooling unit to and from CellarPro or to and from a designated repair facility, and for removing and reinstalling the wine cooling unit from the wine cellar.

The limited warranty applies only to wine cooling units purchased from the factory or an authorized dealer. Damage caused by others or by any cause beyond the control of CellarPro, shall not be considered defects in material or workmanship and are not covered by the warranty. The limited warranty does not cover any parts or labor to correct any defect caused by negligence, commercial use, accident or improper use, maintenance, installation, service or repair.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES, WHICH CELLARPRO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. CELLARPRO WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIES OR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights, which vary from state to state.

To receive parts and/or service and the name of a CellarPro designated repair facility nearest you, contact your CellarPro dealer. You may also contact CellarPro directly by calling us at 1.877.726.8496.

 

  • Energy-efficient EC fans on both the hot and cold sides of the unit.
  • Adjustable humidity control combines a high-output compressor with flexible fan cycles to maintain a recommended level of moisture inside your cellar. 
  • Extra large coils generate maximum cooling power inside the cellar. 
  • Choose from rear (standard) or top exhaust (add-on, no extra cost)
  • Excess condensate is managed with a high-capacity stainless steel condensate pan and 100W electric heating element. 
  • Commercial-grade Electrofin coating protects the evaporator coils from leaks and corrosion. 
  • Intuitive LED display panel mounted on the unit with digital programmable thermostat is simple and easy to use. (see add-on option above for a remote display/control option).
  • Energy-saver mode, quick-chill mode, and auto-defrost cycle.
  • Temperature set point range is 47°F to 62°F when the cooling unit is installed into an appropriately sized cellar.
  • Unit operates with minimal vibrations and less noise than comparable units from other companies.
  • Audible and visual alarms and maintenance-needed indicator protect the cooling unit and the wine cellar.
  • 8 foot power cord exits from the rear of the unit and plugs into a standard 110V receptacle on a dedicated 15amp circuit. If you'd prefer to plug your unit inside the wine cellar, choose the Power Cord Modification add-on.
  • Removable steel case provides access to the internal components for servicing and repair.
  • ETL Tested and Certified to rigorous UL Standards for safety. 

View Configuration Diagrams

  • CellarPro 1800 series cooling units are self-contained and fully-charged. They are designed to be installed through-the-wall or just above the cellar in an air-conditioned space (ie. not a hot attic or other unconditioned space)
  • 1800 series units cannot be front ducted but certain models (XT and XTS) offer rear ducting with the purchase of the rear duct hood or rear duct kit add-on.
  • On the cold side, this unit intakes from the front and exhausts cold air from the bottom (so the front 8 inches of the cooling unit must be inside the cellar.)
  • This unit requires fresh air intake at the rear.
  • If the fresh air intake (on the hot side) will receive air below below 40°F, you will require a compressor heater (see add-on options above).
  • If the fresh air intake (on the hot side) will pull air below 20°F, down to -20°F, you must add both the compressor heater and fan cycling switch (see add-on options above).
  • This unit must always be installed and operated in an upright position.

Cooling Capacity:

1065 BTU/h at 55°F

Dimensions:

18” w x 16 1/2” d x 10 1/2” h

Weight:
60 lbs

Sound:
41 dBA (rear)

Power/Rating:

115V AC / 60 Hz

Compressor Amps:

- Startup (LRA): 14.2 Amps

- Running: 2.4 Amps

- Total Watts: 191

- Requires Dedicated 15-Amp Circuit (surge protector recommended)

Installation Resource Documents

Owners Manual Top/Bottom Cut Sheets
Spec Sheet Installation with a Support Shelf
Installation with Mounting Clips Front/Rear/Side Cut Sheets

Orders of this item are typically shipped within 4 – 8 business days via an LTL carrier, on a pallet.

Please note: If this unit is on backorder or subject to longer lead times, it will be noted in the main product description.

The pallet will be delivered to the first opening in your home (typically a garage).

This product is warrantied by Cellar Pro Cooling Systems.

For five years from the date of purchase, your CellarPro warranty covers the internal compressor if it proves to be defective in materials or workmanship. In addition, for two years from the date of purchase, your CellarPro warranty covers all parts and labor to repair or replace any components in the wine cooling unit that prove to be defective in materials or workmanship.

For all products covered by the terms of this warranty, CellarPro will repair or replace the original cooling unit with a new or refurbished cooling unit and, once replaced, the original cooling unit must be returned to CellarPro.

All service provided by CellarPro under the above warranty must be performed by CellarPro or a designated repair facility unless otherwise specified by CellarPro. Purchaser is responsible for shipping the wine cooling unit to and from CellarPro or to and from a designated repair facility, and for removing and reinstalling the wine cooling unit from the wine cellar.

The limited warranty applies only to wine cooling units purchased from the factory or an authorized dealer. Damage caused by others or by any cause beyond the control of CellarPro, shall not be considered defects in material or workmanship and are not covered by the warranty. The limited warranty does not cover any parts or labor to correct any defect caused by negligence, commercial use, accident or improper use, maintenance, installation, service or repair.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES, WHICH CELLARPRO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. CELLARPRO WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIES OR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights, which vary from state to state.

To receive parts and/or service and the name of a CellarPro designated repair facility nearest you, contact your CellarPro dealer. You may also contact CellarPro directly by calling us at 1.877.726.8496.

 


Recently viewed